Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might discover that your garage door opener has been providing you issues, so you need to fix it. You can repair it by changing a circuit board, a photo-eye sensing unit, the primary drive equipment, or the set-limit switches. You can likewise examine if the security sensors are functioning properly.

Replacing a circuit card

Replacing a motherboard for your garage door opener needs a couple of actions and also devices. First, you require to turn off the circuit breaker as well as disconnect any cables. Next off, open up the motherboard cover. This will assist you to identify the problem and also determine if you need a new board. Next off, eliminate the old board and also its wire adapters.

You can then proceed to replace the motherboard. The replacement process is simple as well as takes about 10 mins. A brand-new circuit board will set you back about $80. To shield your new circuit board from power rises, you can buy a rise protector.

Changing a photo-eye sensing unit

Changing a photo-eye sensing unit can be a relatively basic task. Initially, get rid of the sensor from the door and also make sure it is located properly. If the sensor is angled whatsoever, it may not be getting the appropriate signal, which might be triggering the strobe lights. If you notice that the photo-eyes run out alignment, you might need to have actually a technician come and fix the issue.

The photo-eye sensing unit includes two pieces that mount on the outside of the door tracks and also towards the floor. The image eyes will have a small LED light as well as need to be solid in color. If the light is blinking, its likely the photo-eye is defective as well as will certainly need to be changed.

Changing a primary drive equipment

To change a garage door opener main drive equipment, begin by getting rid of the cap from the chain pulley. Next off, eliminate both screws holding the drive equipment to the sprocket assembly. Now, you can unfasten the 3 stress pins. Squeeze them from both sides and after that remove them. Then, separate the 3 cables from the garage door opener electric motor. These cables need to be white, red, and blue.

Once you have actually eliminated the old gear, install a new one. Make certain to oil it well. Place the new gear right into the shaft, making sure to line up the placing holes. Ensure the equipment and also gear setting up are located properly to make sure smooth operation. Next, make use of a hammer as well as a nail to drive a pin into the new equipment.

Adjusting the set-limit buttons

The first thing you need to do if your garage door is not working effectively is to check the set-limit switches. You might need to adjust them to make sure that the door shuts earlier or stops prior to it reaches the floor. You can inspect this by checking out your garage doors handbook or online.

To change the set-limit switches, youll require a screwdriver or outlet. Change the knob clockwise or counterclockwise until the door goes up as well as quits, or minimizes its range. To look for appropriate travel distance, gauge the gap from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Key St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *